高新技能企业 · 轿车深度维护品专业供货商

全国招商热线:13318861726

当时方位:主页 > 产品中心 > UD 优道 > 冷却体系冷却体系
优道环保冷却液

称号:无水冷却液(又叫无水冷却液,无水防冻液) 
品牌:优道UD     
技能来历:美国陶氏化学与美国LUBRIZOL-UD的原料及技能支持

成效:具有抗腐蚀,高沸点 低凝点,热平衡,增动力降排放,省燃油的特性,一次参加毕生无需替换,下降成本 。恢复发起机正常温度,增强发起机动力。

运用范围:各品牌轿车冷却体系的冷却和防冻。(高沸点:180℃,低凝点:-60℃)。千万车主见证效果。

  • 优道环保冷却液
  • 优道环保冷却液

品牌:UD优道

体系:冷却体系

产品编号:UD-02.115-1/1000ML

企业规范:Q/YKJH 47

产品仅供4S店运用


产品特色:

1、优道无水环保冷却油(冷却液)选用高沸点结合高效的抗泡配方,并参阅德国国家实验室冷却剂抗腐技能,由高档多元醇,抗氧剂,防气蚀剂等多种增加剂精制而成,

2、沸点高、冰点低。(沸点:190℃  凝点:-60℃),不结冰耐酷寒,完全消除“开锅”烦恼,热车可随时翻开水箱盖。

3、无铁锈、无水垢、无腐蚀、无气蚀、无蒸腾、无压力。延长了发起机部件的运用寿命,削减修理和替换。

4、有用改进和平衡发起机的温度,削减发起机的磨损,提高发起机功能。

5、缩短发起机启动时升至正常温度的时刻,下降发起机噪音,削减废气排放。

6、消除汽缸顶部“过热极点”现象,防自燃、防爆震。增加扭矩,增强动力、下降油耗。

7、高品质产品,一次加注,经久耐用,真实无需替换的冷却油。


运用方法:

1、施工目标:

新车、磨合期后的车


2、施工操作流程:

(1)、车辆进入工位后翻开暖风,对发起机进行惯例查看:发起机水温、毛病灯、暖风状况、冷却体系检漏。(如有渗漏修理后再操作)

(2)、拧开放水开关或拆开下水管,把原车冷却水放掉,拧紧放水开关或装好下水管。

(3)、等发起机降温后往水箱里加进清水,起动发起机让冷却体系进行清洗,清洗进程加油门让节温器翻开(不开空调时电扇滚动)

(4)、清洗完成后拧开放水开关把水放掉,拆开上、下水管,暖风管、中缸放水螺丝、副水箱(若螺丝太紧主张不拆),有双空调的车型,还需撤除后排暖风管。

(5)、等发起机降温后用清水清洗整个冷却体系一遍,如水箱、缸休、暖风箱、副水箱等。

(6)、用UD专业风枪把冷却体系的水吹洁净。吹水流程:(1)吹洁清水箱内的冷却水。(2)吹洁净缸体内的的冷却水。(3)吹洁净暖水箱内的冷却水(确保出水管无水珠则可)。

(7)往中缸加注500毫升优道除水剂,用风吹出来(用杯接住),用测水仪测含水量(须测3次以上)仪器刻度达53以上,再把缸休中的除水剂吹洁净。

(8)、拧紧放水开关,装上上、下水管、暖风管、中缸放水螺丝(注:留一条方位高的管不装,加注无水冷却油时让它排空气),清洗吹干后装上副水箱。

(9)、往水箱里增加无水冷却油,增加进程用手指捏上下水管进行排空(如该车型有放空螺丝则拧开螺丝进行排空),当水箱里的冷却油加满时,起动发起机踩油门让节温器翻开(加快到2500转/分,亲近留心水温改变及管道状况)。

(10)、再往水箱及副水箱增加无水冷却油直到规范液面,拧上水箱盖路途试车,路试后翻开水箱盖测无水冷却油中的水含量,仪器刻度达53以上,并查看无水冷却液的液面高度(不行时增加到规范液面)。

(11)、查看各水管有没漏水,冷却体系是否正常,在水箱盖和车尾贴上UD发起机环保冷却油正告标志,避免再次参加传统冷却液和水。


误区and注意事项!!!!

误区和注意事项一:用自来水或许不合规范的冷却液来代替无水冷却油,或是在有优道无水冷却油上混合自来水或许不合规范或是含水的冷却液来运用? 一会影响本品的功能 ,二是会出现以下几种状况。

误区和注意事项二:行车时发现冷却液不行发起机温度偏高,这时车上没有UD冷却油,则能够增加一些纯清水先解当务之急,然后有条件时再把冷却液完全替换成UD冷却油,恢恢复车功能。


Product features:

1. Youdao water-free and environment-friendly cooling oil (coolant) adopts high-boiling point combined with high-efficient anti-foaming formula, and refers to the anti-corrosion technology of Germany national laboratory coolant, which is refined from advanced polyol, anti-oxygen agent, anti-cavitation agent and other additives.

2. High boiling point and low freezing point. (boiling point: 190 ℃ solidifying point: 60 ℃), not ice cold resistant, eliminate "boiled" worry, hot car can open the tank cover at any time.

3. No rust, no scale, no corrosion, no cavitation, no evaporation, no pressure. Extended the service life of engine parts, reduce maintenance and replacement.

4. Effectively improve and balance engine temperature, reduce engine wear and improve engine performance.

5. Shorten the time to reach the normal temperature when the engine starts up, reduce the noise of the engine and reduce the exhaust emissions.

6. Eliminate the phenomenon of "superheated vertex" on the top of cylinder, and prevent spontaneous combustion and explosion - proof shock. Increase torque, increase power and reduce fuel consumption.

7. High quality products, one time injection, durable, really no need to replace the cooling oil.


Usage:

1. Construction objects:

A new car, a car after a period of wear and tear


2. Construction operation process:

(1) after entering the station, the vehicle will turn on the warm air and carry out routine inspection of the engine: the temperature of the engine, the fault lights, the warm air and the leakage detection of the cooling system. (if there is leakage, it can be operated after maintenance)

(2) turn on the water switch or open the downpipe, release the cooling water from the original car, tighten the water discharge switch or install the downpipe.

(3) after the engine cools down, add water into the water tank, start the engine and allow the cooling system to be cleaned, and open the fuel valve during cleaning (the fan turns when the air conditioner is not switched on).

(4) after the cleaning, turn the open water switch to release the water, and open the upper and lower water pipes, the warm air pipes, the central cylinder drain screws, the auxiliary water tanks (if the screws are too tight, it is recommended not to remove).

(5) after the engine cools down, clean the entire cooling system with clean water, such as water tank, tank rest, warm air box and auxiliary water tank.

(6) blow the water out of the cooling system with the UD professional air gun. Blow water flow :(1) blow the cooling water in the clean water tank. (2) blow the cooling water inside the cylinder. (3) clean and warm the cooling water in the water tank (make sure there are no water drops in the outlet pipe).

(7) add 500ml of water remover to the middle cylinder, blow it out with the wind (catch it with the cup), measure the water content with the water meter (more than 3 times must be measured), and then blow the water remover out of the tank rest.

(8) tighten the water discharge switch, install the up and down pipes, warm air pipes, and water discharge screws in the middle cylinder (note: leave a high position pipe uninstalled, and let it drain air when adding water cooling oil), clean and dry it and install the auxiliary water tank.

(9), to add without water cooling oil in the tank, adding process with fingers up and down the pipe emptying (such as the model has a vent screw is unscrewed the screw for emptying), when the cooling oil in the tank filled with starting the engine thermostat open on the accelerator (up to 2500 RPM, closely monitor water temperature change and the status of the pipe).

(10) add water-free but oil-free oil to the water tank and the auxiliary water tank to the standard liquid level, screw on the road test of the water tank cover, open the water tank cover after the road test to measure the water content in the water-free but oil-free water cooling oil.

(11) check whether the water pipes are leaking and whether the cooling system is normal. Affix the warning mark of UD engine environmental cooling oil on the cover of the water tank and the rear of the car, so as not to add the traditional cooling fluid and water again.



Error and attention!!!

Myth and cautions 1: use tap water or substandard coolant instead of water-free oil, or mix tap water with water-free oil or non-standard or water-containing coolant in a preferred channel? It will affect the performance of this product for a while.

Mistake area and notice item 2: when driving, discover coolant is insufficient engine temperature is on the high side, do not have UD coolant oil on the car at this time, can add a few pure water to solve urgent need first, when have the condition, change coolant thoroughly into UD coolant oil, restore original car performance.




回来顶部